georgia aluminum hourglass sleeve load limit

Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

  • 1/16' Aluminum Sleeve (Bag Qty. of 100)

    2 days agou2002·u20021/16 in. aluminum duplex sleeves, sometimes called hourglass sleeves, or oval sleeves. Max After Swage Dimension: 0.185 in. Bag Quantity of 100If properly swaged the termination efficiency for the aluminum sleeve will be 90%.Aluminum sleeves are not recommended when using stainless steel cable, use Zinc Plated Copper Sleeves instead.. …

    Get Price
  • Weight Load Guidelines - Griplock Systems, LLC

    Multiply the result by the factor beneath the angle from the vertical in the chart below. If the weight per cable is 20 lbs. and the angle is 60°, the force on the cable = 20 0.50 = 40 lbs. Angles over 60° from the vertical are not recommended. For help with this …

    Get Price
  • HVAC Duct Construction Standards - Public.Resource.Org

    2017-10-2u2002·u2002NOTES FOR SPECIFIER; 1.0 DUCT CONSTRUCTION Ductwork and supports shall conform to the HVAC Duct Construction Standards, Metal, and Flexible, Second Edition, 1995. Where fittings of configurations not shown in the HVAC-DCS are shown on the contract drawings, they shall be constructed as though they were therein.

    Get Price
  • HOLLOW STRUCTURAL SECTIONS - cousesteel.com

    2005-3-28u2002·u2002load of 152 kips. The largest effective length, KL, is 20 feet. Enter the Fy = 46 ksi table (page 8) for the 8-inch square ERW HSS. Read across the row at KL = 20 and note the following: 8 x 8 x 5/8 can carry 296 kips > 152 kips - O.K. x 1/2 can carry 247 kips > 152 kips - O K. x 3/8 can carry 193 kips > 152 kips - O.K

    Get Price
  • Mechanical seal technology and selection -

    Load factor The balance ratio is just a non-dimensional factor used to assess a mechanical seal. A second one is the load factor . The balance ratio and the load factor are practically identical when the pressure differentials to be sealed are large. The friction at the dynamic secondary seals p r is usually disregarded in the calculation.

    Get Price
  • How to Select and Use Swage Sleeves - E-Rigging

    2018-1-12u2002·u2002It is important to note that aluminum sleeves are NOT recommended for stainless steel cable because of the possibility of the aluminum corroding when in contact with stainless steel. Over time this may cause the contact between the sleeve and cable to weaken and make an unsafe assembly.

    Get Price
  • Round, Square and Rectangular Tube & Pipe

    2021-12-3u2002·u2002Steel Tube & Pipe ® 4-4 alro.com Alro Steel Metals Guide 4 x 2 14 ga 0.083 3.293 11 ga 0.125 4.750 10 ga 0.134 5.070 8 ga 0.165 6.130 7 ga 0.188 6.870

    Get Price
  • purlins, rails & eaves beams

    2016-6-21u2002·u2002LOAD TABLES ON PAGE 33 HEAVY END-BAY SINGLE-SPAN SYSTEM This is a highly efficient sleeved-system, with sleeves at all supports thus allowing a form of continuous beam design. Inner bay sections and sleeves are thinner than at the end bay

    Get Price
  • Hourglass

    LOGIN . 2021 © Imarketslive.

    Get Price
  • American Wire Gauge Conductor Size Table

    2016-8-30u2002·u2002For example, replace a No. 6 AWG, copper, type TW conductor with an aluminum conductor. Table 310-16 lists the ampacity of No. 6 copper TW (60°C colu mn) at 55 amperes. Now select an aluminum conductor from the 60°C column that has an ampacity of 55 amperes or higher. A No. 4 aluminum would be used to replace the No. 6 copper TW conductor.

    Get Price